1-Chip DLP™ Projectors PT-RQ7 Series

PT-RZ7L

AVAILABLE FROM CY2024 Q3

WUXGA: With High contrast and vibrant colors

Scroll down

Key features

Compact: Lightweight design for easy setup and transport.
Wide Scalability: Intel® SDM-compatible slot for flexible, streamlined integration.
Eco-Friendly Innovation with Proven Reliability and Recycled Materials.
PT-RQ7LPT-RQ6LPT-RZ7LPT-RZ6L
7,500 lm2 /
7,500 lm (ANSI)3 /
7,700 lm (Center)4
6,500 lm2 /
6,500 lm (ANSI)3 /
6,700 lm (Center)4
7,500 lm2 /
7,500 lm (ANSI)3 /
7,700 lm (Center)4
6,500 lm2 /
6,500 lm (ANSI)3 /
6,700 lm (Center)4
4K (3840 x 2160 pixels)54K (3840 x 2160 pixels)5WUXGA (1920 x 1200 pixels)WUXGA (1920 x 1200 pixels)

1 PT-RQ7L/RQ6L only.
2 When ET-DLE170 is attached. Measurement, measuring conditions, and method of notation all comply with ISO/IEC 21118: 2020 international standards. Value is the average of all products when shipped.
3 Measurement, measuring conditions, and method of notation all comply with American National Standards Institute standards. Value is the average of all products when shipped.
4 Average light-output value of all shipped products measured at the center of the screen in NORMAL Mode.
5 Maximum physical resolution of 4K (3840 x 2160) with Quad Pixel Drive [ON].
6 PT-RQ7L/RQ6L only. Supports input signals up to 1080p. The display frame rate corresponds to the input signal frame rate. When using the PT-RQ7L/RQ6L to display 1080/100p, 1080/120p, or 1080/240p content, edge blending and geometric adjustment cannot be used.
7 Input signals to the PT-RZ7L/RZ6L are converted to the projector’s display resolution upon playback. YPBPR 4:2:0 format only for 4K/60p and 4K/50p signals input via DIGITAL LINK.
8 PT-RQ7L/RQ6L only. Optional ET-SWR10 Real-Time Tracking Projection-Mapping System is sold separately.
9 Optional proprietary and third-party function boards compatible with the Intel® SDM standard-compatible SLOT are sold separately. Panasonic cannot guarantee the operation of third-party devices.
10 The Dust Protected performance of this unit is not guaranteed to be free from damage or failure under all conditions (environment with conductive dust, etc.). Please use an enclosure in environments with smoke containing oil, salt, and moisture.
11 Around this time, the light output will have decreased by approximately 50 %. IEC62087: 2008 Broadcast Contents, [NORMAL] Mode, [PICTURE MODE] set to [DYNAMIC], Dynamic Contrast [3], temperature 35 °C (95 °F), elevation 700 m (2,297 ft) with 0.15 mg/m3 of airborne particulate matter. Panasonic recommends a checkup at the point of purchase after about 20,000 hours. Light-source lifetime may be reduced depending on environmental conditions. Replacement of parts other than the light source may be required in a shorter period. Estimated maintenance time varies depending on the environment.
12 By weight of the total mass of plastic parts in the projector main unit. Excludes projection lenses, printed circuit boards, labels, cables, connectors, electronic components, color sensor cases, optical components, ESD components, EMI component adhesives, and coatings.

Feel free to reach out to us for any further questions or more information about the RQ7 Series.

Thank you, we've received your submission, and we'll be in touch soon!

 

Compact: Lightweight design for easy setup and transport.

Rich Color Enhancer Brings the Creator’s Work to Life

Rich Color Enhancer is an original 2-mode color optimization technology. Dynamic Mode balances brightness and color for clear visibility in bright environments. Standard Mode optimizes color reproduction by expanding red-channel output for vibrant red expression. This is critical for the accurate and immersive reproduction of artwork and other color-rich content.

Digital Art Mode Increases Visual Impact

Digital Art Mode is a new picture mode that optimizes the presentation of high-quality digital artwork in museums, galleries, and immersive entertainment spaces. This mode allows you to easily enhance projection quality, emphasizing high contrast and vivid color reproduction for a more impactful viewing experience.

Note: Graphic is simulated for illustrative purposes only.

 

Wide Scalability: Intel® SDM-compatible slot for flexible, streamlined integration.

Supports New Media Processors to Simplify Multi-Projection

The RQ7 Series works with Panasonic’s ET-FMP50 Series media processors to simplify multi-projection complexity. The processors, which comprise box-type and function board-type for the projector's Intel® SDM standard-compatible SLOT, feature automatic camera-based1 warping/blending and 4K media playback capabilities.

1 Compatible cameras (sold separately) comprise NIKON® D5200/D5300/D5500/D5600/D7500/Z50.

Wide Scalability with Intel® SDM Standard-Compatible SLOT

The RQ7 Series is compatible with optional proprietary and third-party function boards that insert into its Intel® SDM standard-compatible SLOT, making it easy to adapt, scale, and expand your projector’s connectivity.

Note: The terminal layout pictured is for reference only. Optional proprietary and third-party function boards are sold separately. Panasonic cannot guarantee the operation of third-party devices. The transmission method to the slot must be by HDMI™ signal.

1 Available free from the App Store or the Google Play Store. Check device and OS compatibility before downloading and installing the app.
2 Some devices do not support the projector autofocus function.
3 When projecting a 300-inch image. The maximum distance is 3 m (10 ft) for a 100-inch image.
4 Requires optional AJ-WM50 Series Wireless Module (sold separately). Product availability may vary by country or region.

Geo Pro Automates Screen Adjustment and Blending

RQ7 Series offers built-in geometric adjustment tools, including a point-based Free Grid function to correct localized screen distortion. It ships with preactivated upgrade kit licenses for Geo Pro software. These comprise the ET-UK20 Geometry Manager Pro Software Upgrade Kit, which expands functionality and adds sophisticated line, shape, and bitmap masking tools, and the ET-CUK10 Auto Screen Adjustment Upgrade Kit, which automates edge-blending including brightness, color, and black level adjustment via a camera.

Note: Visit PASS to register your projector and download free Geometry Manager Pro software for Windows®. Compatible cameras comprise Nikon D5200/D5300/D5500/D5600/D7500. Other conditions apply. Please visit PASS for more information.

Contrast Sync and Shutter Sync via LAN Cable Only

Traditionally, Dynamic Contrast control operated individually for each projector in a multi-screen system, leading to step noise in blends due to variations in the Average Picture Level (APL). Panasonic’s Contrast Sync resolves this issue by using the average APL of all projectors in the system, resulting in a seamless multi-screen image. The RQ7 Series is the first Panasonic projector to support Contrast Sync via LAN cable only, eliminating the need for a serial cable connection and reducing system complexity. Additionally, the shutter timing of all sub-projectors is synchronized with the main projector via the LAN connection, ensuring cohesive fade-in/fade-out effects across the entire projection.

Import and Save Custom Test Patterns

In addition to 10x built-in test patterns, users can import and save 4x custom images in JPEG, BMP, or PNG format to an RQ7 Series projector via its Web Control UI or USB memory device for use as test patterns, start-up logos, and no-signal screensavers. Installers can calibrate projectors using client content or custom images without connecting to a media source device.

Note: This function replaces Logo Transfer Software.

Quickly Find the Projection Angle with Angle Monitor

RQ7 Series supports 360° projection angles, enabling image mapping on floors, walls, and 3D objects. However, aligning the projection angle with the design simulation can be challenging and requires two people. The projectors feature a built-in gyro sensor detecting changes in the projector’s pitch and roll angles, graphically displayed in the OSD settings menu. Installers can adjust the projection angle without needing assistance.

Note: The displayed values are based on the results of angle sensor detection and may differ from the actual projection angle. They are for reference only, and accuracy is not guaranteed.

Refreshed Web Control User Interface

RQ7 Series supports 360° projection angles, enabling image mapping on floors, walls, and 3D objects. However, aligning the projection angle with the design simulation can be challenging and requires two people. The projectors feature a built-in gyro sensor detecting changes in the projector’s pitch and roll angles, graphically displayed in the OSD settings menu. Installers can adjust the projection angle without needing assistance.

Note: The displayed values are based on the results of angle sensor detection and may differ from the actual projection angle. They are for reference only, and accuracy is not guaranteed.

 

Eco-Friendly Innovation with Proven Reliability and Recycled Materials.

PT-RQ:RZ Series - Dust-Resistant Optical Engine 1

1 The Dust Protected performance of this unit is not guaranteed to be free from damage or failure under all conditions (environment with conductive dust, etc.). Please use an enclosure in environments with smoke containing oil, salt, and moisture.
2 Around this time, the light output will have decreased by approximately 50 %. IEC62087: 2008 Broadcast Contents, [NORMAL] Mode, [PICTURE MODE] set to [DYNAMIC], Dynamic Contrast [3], temperature 35 °C (95 °F), elevation 700 m (2,297 ft) with 0.15 mg/m3 of airborne particulate matter. Panasonic recommends a checkup at the point of purchase after about 20,000 hours. Light-source lifetime may be reduced depending on environmental conditions. Replacement of parts other than the light source may be required in a shorter period. Estimated maintenance time varies depending on the environment.

Eco Boost Maintains Perceived Brightness with Reduced Consumption

A new Eco Boost mode further reduces energy consumption when Dynamic Contrast is enabled while maintaining perceived brightness.

Note: Graphic is simulated for illustrative purposes only.

Reducing Environmental Impact with Recycled Materials

In addition to using responsibly procured materials, the plastic parts in the main projector body contain about 73%1 recycled resins, reducing the utilization of virgin materials. By supporting eco-friendly manufacturing processes and pursuing recycling-based programs at end-of-life, your organization helps minimize environmental impact throughout the product’s lifecycle.

1 By weight of the total mass of plastic parts in the projector main unit. Excludes projection lenses, printed circuit boards, labels, cables, connectors, electronic components, color sensor cases, optical components, ESD components, EMI component adhesives, and coatings.

Backup Input Redundancy

Two identical signals can be simultaneously transmitted to HDMI™ 1 (Primary) and HDMI™ 2 (Backup). If transmission to the primary input is interrupted, the projector switches to the backup automatically in a minimum of 0.3 seconds1 without screen-blanking. This layer of insurance gives greater peace of mind during events where image display can’t be interrupted.

1 Varies depending on the Backup Input mode and the connected external device.
Note: Primary and backup terminal assignments are fixed. The input signals to primary and backup inputs must be identical.

Multi-Laser Drive Engine Enhances Reliability

Multiple laser modules are equipped with Failover Circuitry. In the unlikely event a single diode fails, Failover Circuitry continues to supply electricity to the functional diodes in the series, minimizing brightness loss. If the same issue were to occur in projectors without Failover Circuitry, all diodes in the module might shut down, resulting in a significant loss of brightness.

Reduce Errors with Remote Preview LITE

Remote Preview LITE allows projectionists to confirm connectivity and assess image adjustments before the video is projected by viewing preview thumbnails on a laptop. This is valuable at live events where checking content on the screen is limited due to soundchecks and other logistical factors. Accessible via software or web browser, it works with the projector in Standby1 or with the shutter on, minimizing errors before performances.

1 Projector must be set to Pre-Show Mode.
Note: Requires Multi-Monitoring & Control Software Version 3.3 or later.

Other Features

  • Supports Art-Net DMX, PJLink™, Crestron Connected® V2, Crestron® XiO Cloud, and Extron XTP®
  • Supports IPv61 network protocol
  • Supports widescreen 21:9 input signals
  • USB port for DC 5 V/2 A power supply, optional AJ-WM50 Series
    Wireless Module, and data transfer
  • Compatible with the Multiple PJ Firmware Batch Update Tool
  • Data-Cloning Function2 via LAN or USB
  • Quick Start and Quick Off
  • Multi-screen Support System
  • Multi-Unit Brightness and Color Control
  • DICOM Simulation Mode
  • Waveform Monitor Function

1 Optional AJ-WM50 Series Wireless Module is not compatible with IPv6.
2 Data cloning is supported among models in the same series with the same resolution. Passwords, projector ID, and network settings are excluded.

Specifications table

Projector type1-Chip DLP™ projector 
DLP™ Chip | Panel Size17.0 mm (0.67 in) diagonal (16:10 aspect ratio) 
DLP™ chip | Number of Pixels2,304,000 (1920 x 1200 pixels) 
Light SourceLaser diodes 
ResolutionWUXGA (1920 x 1200 pixels) 
Contrast Ratio*215,000:1 (Full On/Full Off, Dynamic Contrast [3]) 
Screen Size (Diagonal)1.27–5.08 m (50–200 in) with ET-DLE055, 1.27–15.24 m (50–600 in) with ET-DLE060/ET-DLE085/ET-DLE105/ET-DLE150/ET-DLE170/ET-DLE250/ET-DLE350/ ET-DLE450, 2.54–8.89 m (100–350 in) with ET-DLE035, 2.54–10.16 m (100–400 in) with ET-DLE020G/ET-DLE020 

Accessories & Software

Lenses for 1-Chip DLP

ET-DLE085

0.8-1.0:1 throw ratio (WUXGA)

Lenses for 1-Chip DLP

ET-DLE150

1.3-1.9:1 throw ratio (WUXGA)

Lenses for 1-Chip DLP

ET-DLE250

2.3-3.6:1 throw ratio (WUXGA) 

Lenses for 1-Chip DLP

ET-DLE350

3.6-5.4:1 throw ratio (WUXGA)

Showing 4 of 10

Brackets

ET-PKD120H

High ceiling mount bracket

Brackets

ET-PKD120S

Low ceiling mount bracket

Brackets

ET-PKD130H

ET-PKD130H

Brackets

ET-PKD130B

Bracket assembly

Showing 4 of 4

DIGITAL LINK Switcher

ET-YFB200G

2 x DIGITAL LINK (based on HDBaseT™ technology) terminals output uncompressed HD digital video, audio and command signals to two projectors/displays.

Showing 1 of 1

DIGITAL LINK Switcher

ET-YFB200G

2 x DIGITAL LINK (based on HDBaseT™ technology) terminals output uncompressed HD digital video, audio and command signals to two projectors/displays.

Showing 1 of 1

APantac SDM - compatible with Panasonic

SDM board

TY-SDVoE-SDM

SDVoE Receiver for SDM

Apantac SDM - compatible with Panasonic

SDM board

TY-SDI-HDTV-SDM

12G SDI Receiver for SDM

Apantac SDM - compatible with Panasonic

SDM board

TY-HDBT-SDM

UHD HDBaseT Receiver for SDM-S and SDM-L

SDM board

TY-SB01FB

12G-SDI Optical Function Board

Showing 4 of 5

Metadata Handling

AJ-WM50P

The AJ-WM50 is the dual band, compact wireless module for P2HD and AG-DVX200 camera recorders.

The WM50 dual band (2.4GHz and 5GHz) makes for a more reliable, stable connection to a network in various environments yet its compact size enables it to fit in the wireless module compartment of the P2HD cameras. 2.4GHz offers strong connection through obstacles and compatible with many devices whereas 5GHz offers stability from radio wave interference (Microwave, Bluetooth, etc).

Showing 1 of 1

Metadata Handling

AJ-WM50P

The AJ-WM50 is the dual band, compact wireless module for P2HD and AG-DVX200 camera recorders.

The WM50 dual band (2.4GHz and 5GHz) makes for a more reliable, stable connection to a network in various environments yet its compact size enables it to fit in the wireless module compartment of the P2HD cameras. 2.4GHz offers strong connection through obstacles and compatible with many devices whereas 5GHz offers stability from radio wave interference (Microwave, Bluetooth, etc).

Showing 1 of 1

PressIT

TY-WPS1 series

“PressIT” is Panasonic’s Wireless Presentation System that allows easy screen collaboration with just a single press of a button. This elegant solution, designed to make collaboration quick and simple in meeting rooms, can connect up to 32 devices at one time, allowing users to present on screen or via a projector at the touch of a button..

Showing 1 of 1

AVAILABLE FROM CY2024 Q4

Media Processor

ET-SBFMP10

Media Processors Simplify Multi-Projection Workflows for Immersive Experiences

Media Processor

ET-FMP20

Media Processors Simplify Multi-Projection Workflows for Immersive Experiences

Media Processor

ET-FMP50

Media Processors Simplify Multi-Projection Workflows for Immersive Experiences

Showing 3 of 3

AVAILABLE FROM CY2024 Q4

Media Processor

ET-SBFMP10

Media Processors Simplify Multi-Projection Workflows for Immersive Experiences

Media Processor

ET-FMP20

Media Processors Simplify Multi-Projection Workflows for Immersive Experiences

Media Processor

ET-FMP50

Media Processors Simplify Multi-Projection Workflows for Immersive Experiences

Showing 3 of 3

Related resources

Showing 12 of 46

Sorry there was an error...
The files you selected could not be downloaded as they do not exist.

You selected items.
Continue to select additional items or download selected items together as a zip file.

You selected 1 item.
Continue to select additional items or download the selected item directly.

Download selected file